Extron-electronics DVI 201 User Guide Manual do Utilizador

68-1034-02 Rev. D04 10DVI Twisted Pair ExtenderDVI 201User GuideDVI & HDMI Extenders

UL guidelines for rack mountingThe following Underwriters Laboratories (UL) guidelines pertain to the installation of a DVI 201 unit onto a rack.1. E

1U Universal Rack Shelf Figure 3. Mounting the Transmitter or Receiver on a Universal Rack ShelfFurniture mountingUnder-furniture mountingThe unit can

Through-furniture mountingThe transmitter or receiver can be mounted through a desk or other furniture using an optional Extron MBD 129 through-desk m

Projector mountingThe receiver can be mounted on a projector bracket using either of the following optional Extron projector mounting kits:• PMK 300

NOTE: The PMK 300 has a hole in the bottom plate that allows the projector pole to be inserted through the center of the plate (figure 7), rather than

PMK 350 mountingMount the receiver to a PMK 350 bracket as follows:1. Remove the front and rear plates from the PMK 350 (figure 8), using an Extron Tw

7. Align the two slotted holes in the bottom of the L-shaped bracket with the two slotted holes in the base of the tray. Secure the L-shaped bracket

Decora Unit MountingThe DVI 201 A D (Decora) transmitter and receiver can be installed in a one-gang electrical wall box with a Decora wall plate cove

1. If a wall box is not available to use for a template, see the dimensions on page 35 to create a template. If installing directly into furniture,

Final installationAfter testing and making any adjustments, do the following:1. At the power outlet, unplug the power supply.NOTE: One power supply

This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipme

ConnectionsTransmitter ConnectionsThe wall-mountable transmitter is in an enclosure that can be mounted in UL standard wall boxes with Decora-style fa

POWER 12V 0.4A MAX DVI 201 TxRS-232 PASS THRU Tx Rx DDC ROUTE 1 2 REMOTE SPARE LOCAL POWER12V 0.4A MAXLAUDIOOUTPUTRDO NOT CONNECTTO

Connect the free ends of the same TP cables from the transmitter to the female Input RJ-45 connectors (item h on page 20) on the receiver. See TP c

Receiver ConnectionsThe rack-mountable receiver is in quarter rack width enclosure. The wall-mountable receiver is in an enclosure that can be mounte

h Receiver input ports — Connect one end of the two separate TP cables from the transmitter output connectors (item f on page 17) to these RJ-45 fema

l RS-232 (Control) Pass Thru connector — Connect a serial communications port to this 3.5 mm, 3-pole captive screw connector for bidirectional RS-232

TP cable terminationFigure 21 details the recommended termination of TP cables with RJ-45 connectors in accordance with either the TIA/EIA T 568A or t

Terminating shielded cableThe Tx and Rx each include two shielded RJ-45 connectors and a length of self-adhesive shielded tape that you can use to mak

Power supply wiringNOTES: • Only one power supply is required. A single power supply connected to either unit in the pair powers both units. • A

RS-232 connector wiringFigure 26 shows how to wire the RS-232 connector for non-Decora and Decora units.GroundReceive pin on connected unitTransmit pi

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

OperationFigure 27 shows the DDC control and power indicator on the non-Decora transmitter. Figure 28 shows the power indicator on the Decora transmi

Transmitter DDC Control and Power Indicatora Power LED —DVI 201 Tx (non-Decora) — This front panel LED lights green to indicate that the unit is recei

Technical Points for Digital Video and Content Protection Encryption• Digital Visual Interface (DVI) is a digital video format that was created by th

Application ExamplesAudio ConversionFigure 29 shows a standard installation with DVI video and an audio input. The DVI 201 A D Tx converts the video

Reference InformationThis section discusses the specifications, part numbers, and accessories for the DVI 201. Topics that are covered, include:• Spe

Video output— receiversNumber/signal type ... 1 single link DVI-D (or HDMI*)ConnectorsDVI 201 Rx ... 2 femal

Control/remote — external device (pass-through)Serial control port inputTransmitter ... RS-232 via (1) 3.5 mm, 3 pole captive s

MTBF ... 30,000 hoursWarranty ... 3 years parts and laborNOTE: Al

Mounting AccessoriesIncluded parts Part numberRSF 123 3-inch deep 1U rack shelf kit 60-190-20RSB 123 3-inch deep 1U rack shelf 60-604-21RSU 126 6-i

Decora Template DimensionsIf you need to create a template, use the dimensions shown on figure 31, below.NOTE: The drawing is not full size or to scal

ContentsIntroduction ... 1About this Manual ... 1About the DVI 201 Tr

Extron WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purc

Introduction• About this Manual• About the DVI 201 Transmitter and Receiver• FeaturesAbout this ManualThis manual describes the Extron® DVI 201 fam

There are two subsets of transmitters and receivers in two different enclosures or form factors:• DVI 201 Tx/Rx — These units are housed in quarter r

TP Cable AdvantagesTwisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial or DVI cable. These transmitter and rec

FeaturesTransmits single link DVI-D signals over two CAT 5/5e/6 cables — Standard twisted pair cables provide an economical, easily installed cable so

Installation and OperationThis section describes the installation and the operation of the DVI 201, including:• Mounting the Transmitter or Receiver•