Extron-electronics MLC 206 AAP EC User Guide Manual do Utilizador descarregar pdf (Página 37)

4-5MediaLink Controllers • Serial Communication

The syntax for setting a special function is __ *

# where __ is the function number and

is the value.

To view a function’s setting, use __#, where __ is the function number. In the following table the values of

the

variable are different for each command/function. These values are given in the rightmost column.

Command/response table for special function SIS commands

Command ASCII Command Response

values

(host to MLC) (MLCr to host) and additional descriptions

Delay times

Power on delay 1 *

# WarmUp*

0 = 0 seconds,

1 = 2 seconds,

2 = 4 seconds,

... in 2 second steps up to

150 = 300 seconds (5 minutes).

Example: 1*8# WarmUp*08 Example: set a 16 second power on delay.

Example: 1# WarmUp*023 Example: view the power on delay

setting.

Power off delay 2 *

# CoolDown*

0 = 0 seconds,

1 = 2 seconds,

2 = 4 seconds,... in 2 second

steps up to 150 = 300 seconds.

Example: 2*23# CoolDown*023 Example: set a 46 second power off

delay.

Relays

Relay 1 mode/timing 4 *

# Rly1Tm*

0 = toggle mode (press on/off),

1 = momentary, 1 second long,

2 = momentary, 2 seconds long,

3 = momentary, 3 seconds long.

Example: 4*3# Rly1Tm*3 Example: momentary, 3 sec. long.

Relay 2 mode/timing 5 *

# Rly2Tm*

0 = toggle mode (press on/off),

1 = momentary, 1 second long,

2 = momentary, 2 seconds long,

3 = momentary, 3 seconds long.

Example: 5*0# Rly2Tm*0 Example: set relay to toggle mode.

Relay 3 mode/timing 6 *

# Rly3Tm*

0 = toggle mode (press on/off),

1 = momentary, 1 second long,

2 = momentary, 2 seconds long,

3 = momentary, 3 seconds long.

Associate a button with relay 1 7 *

# Rly1Mode*

Cause a button to control a relay.

For a relay set to be normally closed:

0 = power-on.

1 = power-off.

2-7 = MLC input selection buttons 1-6.

8-27 = remote control module 1 buttons.

28-47 = remote control module 2 buttons.

48-67 = remote control module 3 buttons.

68-87 = remote control module 4 buttons.

For a relay set to be normally open,

add 128 to the above numbers.

128 = power-on (relay normally open).

...

196-215 = remote control module 4

buttons (relay normally open).

127 or 255 = not assigned.

Example: 7*1# Rly1Mode*1 Example: Relay 1 will toggle when

the Display Power button is pressed

for power-off .

Associate a button with relay 2 8 *

# Rly2Mode*

See above.

Associate a button with relay 3 9 *

# Rly3Mode*

See above.

Close a relay 22 * # RlyClosure*

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 71 72

Comentários a estes Manuais

Sem comentários

Extron-electronics MLC 206 AAP EC User Guide Manual do Utilizador Página 37

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Extron-electronics MLC 206 AAP EC User Guide