Extron-electronics SMB 1 Installation Manual do Utilizador descarregar pdf

SMB 1 • Installation Guide

The Extron SMB 1 surface mount box ships with the included

parts shown in the gure to the right. It offers a variety of

mounting options for the TLPPRO320M and TLPPRO520M:

z Stand the box on a suitable surface — The SMB 1 has

two anti-skid pads attached to the bottom that allow it

to stand on a suitable surface without attaching it to the

surface.

z Mount the box with a Swivel Mount Kit — The SMA-1

swivel mount adapter kit (not provided) allows the SMB1

to be permanently mounted for security, but rotated to

provide access to the touchpanel from around the table.

See the SMA-1 Installation Guide, at www.extron.com

before installing the SMB 1.

z Permanently attach the box to a glass surface — Use

the optional GMK 1 kit (not provided). See the GMK 1

Installation Guide, at www.extron.com.

z Secure the box to a suitable surface — This allows the

SMB 1 to be permanently secured to a table-top or wall

(see “Mount the SMB 1 Directly to Furniture or a Wall,”

below).

Bottom Cable

Access Plug

Strain Relief Clamp

Cable Wrap

Strain Relief Boot

SMB 1

Rear Cable

Access Cover

Zip Ties (2 each)

#8 Wood Scr

ews

and washers

(4 each)

#6 Sheet Metal

Screws

(4 each)

#4 Sheet Metal

Screws

(2 each)

Screw Size and Type (Number) and Function

#4-20 x 5/16" Sheet Metal

#8-15 x ¾" Wood

#6-19 x 3/8" Sheet Metal

(2) Secure rear cable access cover

(4) Secure SMB 1 to furniture

(4) Secure wall plate adapter to SMB 1

Mount the SMB 1 Directly to Furniture or a Wall

The illustrations in this section of the guide show the SMB 1 mounted to a table-top or lectern. Wall mounting is identical except

that the base of the SMB 1 is vertical, against the surface of the wall.

ATTENTION:

• Four wood screws are provided to mount the SMB 1 to a table top. To mount the SMB 1 to a wall, use screws and

xtures that are appropriate for the wall material. These are not provided.

• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and

national building codes and local and national electrical codes.

1. Determine where the SMB 1 is to be mounted.

2. Mark the position of the four mounting holes and drill four pilot

holes 3/32inch (2.4 mm) in diameter into the tabletop or wall.

3. If cable access is required through the base of the SMB 1,

remove the hole plug from the bottom cable access hole. Mark

the position of the hole and drill a hole through the table that is

large enough to carry the cables.

4. Secure the SMB 1 to a table-top using the four provided

#8wood screws with washers.

Mounting Holes (4)

#8 Wood Screws

with Washers (4)

Bottom Cable

Access Hole

1 2

Resumo do Conteúdo

Página 1 - SMB 1 • Installation Guide

SMB 1 • Installation GuideThe Extron SMB 1 surface mount box ships with the included parts shown in the gure to the right. It offers a variety of mou

Página 2 - Install the TouchPanel

SMB 1 • Installation Guide (Continued)68-2298-01 Rev. A02 14Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA

Comentários a estes Manuais

Sem comentários

Extron-electronics SMB 1 Installation Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Extron-electronics SMB 1 Installation. Extron Electronics SMB 1 Installation User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Extron-electronics SMB 1 Installation