Extron-electronics MLC 104 SIS Programming and Control Manual do Utilizador

MLC 104 MediaLink™ Controllers5Chapter FiveSIS™ Programming and ControlHost-to-MLC CommunicationsCommand Tables

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-10PRELIMINARYEnable lockout mode 3243X 3X Exe 3 Lock all front pan

5-11MLC 104 Series • SIS™ Programming and ControlPRELIMINARYView power sensor status 8S 8SX213 If the switcher is connected to an ExtronPower Sensor

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-12PRELIMINARYCommand/response table for SIS commands (continued)Com

5-13MLC 104 Series • SIS™ Programming and ControlPRELIMINARYConfigure serial port parameters24Esc X1*X25, X26, X27, X28CPWX1%2AX25%2CX26%2CX27%2CX28 C

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-14PRELIMINARYCommand/response table for SIS commands (continued)Com

5-15MLC 104 Series • SIS™ Programming and ControlPRELIMINARYEthernet data port configuration and useSet global IP port timeout period24Esc 1*X69TC W1%

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-16PRELIMINARYCommand/response table for SIS commands (continued)Com

5-17MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-18PRELIMINARYCommand/response table for SIS commands (continued)Com

5-19MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

MLC 104 Series • SIS™ Programming and Control5-2SIS™ Programming and ControlPRELIMINARYThe MLC 104 Series controller can be remotely set up and contro

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-20PRELIMINARYCommand/response table for SIS commands (continued)Com

5-21MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-22PRELIMINARYCommand/response table for SIS commands (continued)Com

5-23MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-24PRELIMINARYCommand/response table for SIS commands (continued)Com

5-25MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-26PRELIMINARYCommand/response table for SIS commands (continued)Com

5-27MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-28PRELIMINARYCommand/response table for SIS commands (continued)Com

5-29MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web

5-3MLC 104 Series • SIS™ Programming and ControlPRELIMINARY• If the MLC is on, it sends the boot and copyright messages when you first open aTelnet co

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-30PRELIMINARYCommand/response table for SIS commands (continued)Com

5-31PRELIMINARYMLC 104 Series • SIS™ Programming and ControlThe syntax for setting a special function for an MLC is X? * __ # where X? is the value an

SIS™ Programming and Control, cont’d5-32PRELIMINARYMLC 104 Series • SIS™ Programming and ControlCommand/response table for special function SIS comman

5-33PRELIMINARYMLC 104 Series • SIS™ Programming and ControlCommand/response table for special function SIS commands, continuedCommand ASCII Command R

SIS™ Programming and Control, cont’d5-34PRELIMINARYMLC 104 Series • SIS™ Programming and ControlCommand/response table for special function SIS comman

5-35PRELIMINARYMLC 104 Series • SIS™ Programming and ControlCommand/response table for special function SIS commands, continuedCommand ASCII Command R

SIS™ Programming and Control, cont’d5-36PRELIMINARYMLC 104 Series • SIS™ Programming and ControlCommand/response table for special function SIS comman

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-4PRELIMINARYRS-232. The ASCII and URL commands listed in the table

5-5MLC 104 Series • SIS™ Programming and ControlPRELIMINARYX17 = Time in tens of milliseconds to wait until the firstresponse character is received vi

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-6PRELIMINARYX49 = Default name: a combination of the modelnameand t

5-7MLC 104 Series • SIS™ Programming and ControlPRELIMINARYX208 = Display (projector on/off) status as tracked by thedisplay driver0 = display power i

SIS™ Programming and Control, cont’dMLC 104 Series • SIS™ Programming and Control5-8PRELIMINARYCommand/response table for SIS commandsCommand ASCII (T

5-9MLC 104 Series • SIS™ Programming and ControlPRELIMINARYCommand/response table for SIS commands (continued)Command ASCII (Telnet) URL Encoded (Web)