Extron-electronics PoleVault Systems PVS 200, 300, and 400 Manual do Utilizador Página 23
- Página / 50
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
2-11
PoleVault Systems Installation • Installation — Stage 2
2. Pull cables
The following cables need to be installed:
• CAT 5 cables for signal transmission from the
A/V wall plates to the PVS 204SA.
N
For PVT RGB D wall plates, two CAT 5 signal
cables for each input are needed.
Maximum distance from the PVS 204SA to the
Wall plates is 100 feet. The optimum distance
is between 50 and 75 feet.
The CAT 5 cables supplied are terminated to the
TIA 568A standard. Other CAT 5 cables can
be used if they are TIA 568A or 568B standards
and terminated to the same standard at both ends.
• CAT 5 cables for MLC network connection
• PoleVault switcher communication cable from the
MediaLink controller
• Projector communication cables from the
MediaLink controller.
a. Drill cable pathways through any obstructions
(e.g., wall caps, fire-breaks, or horizontal studs).
b. Label the CAT 5 signal cables at both ends with the
supplied labels. Refer to the PVS 204SA User’s Manual
for labeling details.
c. Pull the cabling through the wall from the ceiling space
down to the location of the transmitters and other wall
devices, and out through the openings.
T
Secure cables with cable clamps to provide strain relief.
Trim back the outer foil shield to the point where the
cable exits the cable clamp, and insulate exposed cable
shields with heat shrink to reduce the chance of short
circuits.
Both braided and foil shields should be connected to an
equipment ground at the other end of the cable.
RGB #1A
NOTE Fasten the colored section to the cable first,
then wrap the clear section around it.
2b
Use the supplied labels for clear cable
identification during installation.
Signal Cable Label color
RGB 1A (Input 1 RGB) Orange
RGB 1 B (Input 1 RGB) Orange w/black stripe
RGB 2A (Input 2 RGB) Yellow
RGB 2B (Input 2 RGB) Yellow w/black stripe
Video 3 (Input 3 Composite Vid) Green
Video 4 (Input 1 Composite Vid) Red
2c
Pull the cables at each location.
- PoleVault Systems 1
- Precautions 2
- Introduction 3
- Introduction, cont'd 4
- 1. Room layout 5
- Walking Parallel to a Wall 6
- Each speaker covers 7
- 2. Inventory 8
- PVT CV D 9
- PVT RGB D 9
- — Inventory Overview, cont’d 10
- Projector Bracket 14
- (Bottom Section) 14
- Adjuster Plate 14
- (Top Section) 14
- 1. Mark screen location 15
- 3. Verify the image location 16
- 4. Cut the ceiling tile 17
- 7. Install the Screen 19
- Right Side 20
- Rear View 20
- MLC, PW/RS-232/VC, 50' 21
- IR SERIAL COMM, 50' 21
- CAT 5 Patch, 50' 21
- 1. Install mud rings 22
- 2. Pull cables 23
- 3. Install wall plates 24
- RGB IN # 1 24
- Heat Shrink on 25
- Drain Wire 25
- IR connection 26
- PVS 204SA Switcher Rear Panel 27
- Projector 27
- SPK 18, 25' 28
- 1. Cut ceiling tile 29
- 4. Cable the speakers 30
- 8 Ohm Load 31
- Apply 4 pieces of black putty 32
- MVGA M-M, 3' 33
- V RCA, 3' 33
- 1. Pull the cables 34
- PVS 204SA 35
- Ground ( ) 36
- Transmit (Tx) 36
- Receive (Rx) 36
- Rear Plate 37
- 1. Congure the system 38
- 2. Test the system 40
- 3. Final installation 41
- PoleVault switcher 44
- settings 45
- Sensitivity knob adjustment 45
- Reference Information 46
- MLC 104 IP Plus 47
- PVT CV D and PVT RGB D 47
- VIDEO RGB 48
- Outline of installation steps 50
Manuais e produtos relacionados com Hardware Extron-electronics PoleVault Systems PVS 200, 300, and 400
Hardware Extron-electronics P-2 DA2 WM F, WM F AAP, EC F, D Setup Guide Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Extron-electronics Replacing the AC Power Cord with Flexible Conduit Manual do Utilizador
(2 páginas)
(2 páginas)
Kohler custom Bodyspa 116347-2 manuály
Uživatelské manuály a uživatelské příručky pro Příslušenství pro vodu Kohler custom Bodyspa 116347-2.
Poskytujeme 1 manuály pdf Kohler custom Bodyspa 116347-2 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais