Extron-electronics PVS 405D User Guide Manual do Utilizador

User GuidePVS 405DPoleVault Digital Switcher68-2379-01 Rev. A03 14POLEVAULT SWITCHERS

Rear Panel ConnectionsThis section describes which cables to connect to a PVS 405D Switcher.Rear Panel ConnectorsThe illustration below shows the rear

Outputsf HDMI video output — Connect a suitable display device to this female HDMI digital video output connector. Use the Extron LockIt device to se

NOTES: • Use only the supplied 12 V, 4 A power supply for this switcher.• The PVS 405D power supply can support a typical system: for example, a PV

Final SetupWith an MLC 104 IP Plus as a standard MLC controller in the PoleVault system package, the PVS 405D switcher completed setup should look sim

OperationThis section of the manual discusses the operation of a PVS 405D device. Topics covered include:• Front Panel Overview• Configuration• Res

j VoiceLift level adjustment encoder — This allows the user to adjust the level of the VoiceLift (microphone) input level through 43 positions per ro

Resetting the SwitcherThe switcher can be reset to the factory defaults via the front panel, USB, or RS‑232.The reset button on the front panel is a s

Power Save ModesThe PVS 405D is an ENERGY STAR qualified device, and has five power modes. See table below for mode descriptions.See the “SIS Communic

Setting Up and Optimizing the AudioThe following steps ensure optimal sound is achieved by configuring the switcher. For each step, refer to the secti

Gain ControlIndividual channel input sensitivity controlIndividual channel input gain control adjustments are made by rotating the adjustment encoder

Safety InstructionsSafety Instructions • EnglishWARNING: This symbol, , when used on the product, is intended to alert the user of the presence of u

Bass and treble controlFor optimum audio quality, the audio input levels and the bass and treble controls must all be set up properly. Input audio le

Paging sensitivity adjustmentWhen the Priority Page Sensor, or the PPS 35 microphone interface, or the Priority Page Sensor kit is connected to the Pr

SIS Communication and ControlThe PVS 405D can be configured and controlled via a host computer or other device (such as a control system) attached to

Error ResponsesWhen the PVS 405D receives a valid command, it executes the command and sends a response to the host device. If the unit is unable to e

Symbol Definitions• = Space] = Carriage return with line feed¦ or} = Carriage return with no line feedX! = Video and audio input selection, 1‑5X@ = Au

X1* = EDID (DDC) values: (1‑61), see table belowSIS X1* variables for EDID resolution/refresh rate combination (where X1* = 1 through 61)Resolution Re

X2* = Power save mode/state: 0 = auto power save and standby power mode off (power save off) (default) 1 = set auto power save timer

SIS command definitionsX10) = Default name: combination of model name and last 3 hex pairs of MAC address (for example PVS‑405D‑06‑DE‑2E).X

SIS Command and Response TableCommand ASCII Command(host to switcher)Response(switcher to host) Additional DescriptionInput selectionSelect a Video an

Command ASCII Command(host to switcher)Response(switcher to host) Additional DescriptionInput audio gain and attenuationNOTE: The VoiceLift and Aux i

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rule

Command ASCII Command(host to switcher)Response(switcher to host) Additional DescriptionPower save modePower save offE0PSAV} PsavX2*]Turns off power s

Command ASCII Command(host to switcher)Response(switcher to host) Additional DescriptionView Aux input Signal, Normal, and Peak status5S SigX1)•NormX1

Command ASCII Command(host to switcher)Response(switcher to host) Additional DescriptionEDID MinderNOTES: • The switcher and PVT wallplate have two d

Command ASCII Command(host to switcher)Response(switcher to host) Additional DescriptionSpecial functionsSet lineout modeSet lineout to variable55*1#

Command ASCII (Telnet) (host to switcher)Response (switcher to host)Additional DescriptionDecrement horizontal start value EX3^-HSRT} HsrtX3^*X3*]Decr

Command ASCII (Telnet) (host to switcher)Response (switcher to host)Additional DescriptionQuery updated firmware version4QX12)]Use this command to find

PVS 405D • SIS Communication and Control 30

Using the Extron Product Configuration SoftwareThe Extron PVS 405D Product Configuration Software (PCS) offers another way to control the PVS 405D via

Starting the PVS 405D Product Configuration SoftwareNOTE: The following pages cover PCS version 1.x installations only. If you have installed PCS vers

Figure 15. New Device Page in Emulate/Offline ModeUsing the PVS 405D Product Configuration Software — MenusNOTE: For detailed software navigation ope

Conventions Used in this GuideNotificationsThe following notifications are used in this guide:DANGER: A danger indicates a situation that will result

Save DeviceAll audio, video, input configuration settings, HDCP settings, EDID Minder settings and audio settings from a PVS 405D can be exported to a

If you are not connected to the device, the Update Firmware submenu is not available.2. Click OK. A separate window opens and the details of the devi

Using the PVS 405D Product Configuration Software — PagesThere are two main pages for configuring the PVS 405D: the Configuration page and the Hardwar

Video and audio mute buttonsSelect Video Mute to mute only the video signal. The button turns red when mute is applied.Select Audio Mute to mute only

EDID Minder PageExtron EDID Minder is an EDID management process that automatically manages the EDID information between a digital display device and

Assigning EDIDsTo assign EDID to selected inputs:1. From the inputs screen (table of inputs) on the right, select the desired input or inputs (see fi

Audio Settings PageUsing this page each of the audio inputs can be configured, including setting the input format and the gain (for analog inputs only

Mic/Aux/PagingUsing this page to set the input gain, and where desired, ducking can be enabled and settings configured for both VoiceLift and Aux inpu

Hardware PagesClick on the Hardware tab to open these pages.The Hardware pages options are: • Unit Information • Device Name • Executive/Power Mode

3. Enter a name for the device. The name may be up to 24 alphanumeric characters in length.4. Click Apply. To reset the name of the device, click Re

ContentsIntroduction... 1PVS 405D Description ... 1Input

Reset Device PageThis page allows the user to reset the device to factory defaults. Click on this button to open the page.Figure 27. Reset Device Pag

PVS 405D • Connector Wiring 45Connector WiringThis section of the manual discusses the connector wiring for a PVS 405D device. Topics covered include:

PVS 405D • Connector Wiring 46Terminating the speaker cableTo terminate the cable, strip the end of the cable 0.2 inch (5 mm) and secure the wires in

PVS 405D • Connector Wiring 47Power Supply WiringNOTE: Use only the supplied 12 V, 4 A power supply for this switcher. The PVS 405D power supply can

PVS 405D • Connector Wiring 48RS-232 Connector WiringFigure 33 shows the wiring for the PVS 405D and the MLC 104 IP Plus RS‑232 connectors .MLC 104 I

PVS 405D • Connector Wiring 49For IR communicationConnect the IR/RS‑232 projector communication cable for either RS‑232 or IR projector control.MLC 1

PVS 405D • Connector Wiring 50NOTE: Some projectors require NULL connection wiring, which inverts the Tx and Rx connections. See the projector guide

PVS 405D • Connector Wiring 51Input 5 Connector WiringInput 5 is a dedicated‑audio only input for an auxiliary, stereo, line‑level analog audio signa

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +

Connector Wiring ... 45Speaker Configuration ... 45Terminating the speak

IntroductionThis manual covers the installation, operation, and configuration of the Extron PVS 405D PoleVault Switcher. Throughout the manual, this s

OutputsThe PVS 405D has one HDMI output, an amplified audio output, and a line out audio output for assistive listening or recording devices.Control a

Application Diagram12SIGNAL4AUXSENSITIVITYExtronVLM 2000HVoiceLift Microphonewith Charging StationExtronExtronVLM 2000HVoiceLift Microphonewith Chargi