Extron-electronics SME 100 User Guide Manual do Utilizador Página 175
- Página / 185
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Multicast IP Addressing for Multiple SME100 Installations
When multiple SME100 devices are installed in a system (when the multicast address
is used for push or pull streaming) the streams are managed by the SME100 to avoid
conflicts.
Pull streaming (RTSP)
The SME100 can use one of two multicast streaming IP address assignment methods.
If multicast IP addresses for a network are limited, the various SME100 devices can each
use unassigned port numbers within the available range (1024 to 65535).
NOTE: To prevent conflicts, always check to see if other devices using the same IP
address have already used a port number before using it in the SME100.
The following table shows a typical port assignment for multiple SME100 devices using a
single multicast IP address (RTSP pull streams require four sequential ports).
SME Device SMEIP Multicast IP Multicast Port
SME1
192.168.254.10 239.199.188.138 6000 to 6003
SME2
192.168.254.11 239.199.188.138 6004 to 6007
SME3
192.168.254.12 239.199.188.138 6008 to 6011
When there are different multicast IP addresses available, there is no need for multiple port
numbers and the port number can remain at the default (6000) as shown in the next table.
SME Device SMEIP Multicast IP Multicast Port
SME1
192.168.254.10 239.199.188.138 6000
SME2
192.168.254.11 239.199.188.139 6000
SME3
192.168.254.12 239.199.188.140 6000
To change the SME100 port number for multicast pull streaming, see the
"Port Settings Page" on page 103.
NOTE: The SME100 automatically inserts the ending port number when the initial port
number is entered.
Push streaming (TS/UDP, TS/RTP, ES/RTP)
Push streams to a multicast address generally require only two ports, except for ES/RTP
which requires four. When push streaming from multiple SME100 devices to multicast
addresses, the same IP address rules apply as with pull streaming.
For push streaming, the destination IP and port number are adjusted using the encoder
settings page (see Encoder Settings Page on page 88).
SME100 • Reference Information 169
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Manuais e produtos relacionados com Hardware Extron-electronics SME 100 User Guide
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais